Hot Water Relief Valve Dripping: Normal or a Problem?

You've spotted water dripping from a small brass valve on the side of your hot water system, or a pipe running down the wall and spilling onto the ground outside. It's a little alarming, and it should be: that valve is a safety device, and when it's doing something, it's telling you something. The good news is that a bit of dripping is often completely normal. The less good news is that some dripping isn't.
This is one of the most common things we get asked about across South-Eastern Melbourne, from older Armadale and Malvern homes to apartment buildings in South Yarra and Docklands with a hot water unit on every balcony or in every laundry cupboard. Here's how to work out which camp you're in before you pick up the phone.
What the relief valve actually does
Your hot water system is a sealed vessel full of water that expands when it heats. Cold water going in at about 15°C and coming out at 60°C or more takes up noticeably more room, and that extra volume has to go somewhere. The relief valve (often called the pressure relief valve, or PTR valve on storage systems, where it handles both pressure and temperature) is the escape hatch. If pressure or temperature climbs past a safe limit, it opens and lets water out through a drain pipe.
On a Rheem, Stiebel Eltron or similar storage tank, it's the brass valve with a small lever on top, usually fitted on the side or top of the tank with a copper or plastic drain line running away from it. If you're not sure what you've got, our guide to identifying your Rheem or Stiebel hot water system will help you find the model plate and work out the type.
Don't confuse it with the tempering valve. That's a separate valve, usually near the unit or in the wall, that mixes cold water into the hot so it reaches your taps at a safe 50°C. Tempering valves can weep too, but a dripping tempering valve is a different problem. More on temperature settings in our post on how hot a hot water service should be in Australia.
What's normal
A small amount of water from the drain line while the system is heating is normal. As the tank heats, thermal expansion pushes a little water out. You'll often see drips for the length of the heating cycle, especially in the morning or evening after heavy use, and then nothing once the water is up to temperature.
A rough rule of thumb: if it drips for a while during heating, then stops, and the water coming out is cool or lukewarm, you're most likely looking at ordinary expansion. Watch it over a day or two. A cup or two of water over a heating cycle is nothing to lose sleep over.
What isn't normal
Here's what should have you reaching for the phone:
Constant flow. If water is running or dripping around the clock, including hours after the system has finished heating, the valve is passing when it shouldn't.
A hot or scalding discharge. Water coming out of the drain line that's genuinely hot, not just warm, suggests the unit is overheating or the valve is reacting to excess temperature.
A running pipe. If the drain line is flowing like a small tap, don't wait. Something is wrong with the pressure or the thermostat.
Steam, hissing or banging noises. Steam from the valve or loud knocking from the tank means the unit is running too hot, which is a safety issue as well as a wasted-gas-or-power one.
Corrosion around the valve or tank. Green crust on the brass, rust streaks or a damp patch under the tank point to the valve or the tank itself reaching the end of its life.
Common causes of a problem valve
High mains pressure. Melbourne mains pressure can be well above what a storage tank likes, particularly in lower-lying suburbs. A pressure-limiting valve upstream protects your fittings, and if it's failed or was never installed, the relief valve ends up doing the job. This is common in older homes where the original plumbing has never been updated.
A tired or dirty valve. Relief valves have a spring and a seat. After years of heating cycles, limescale or tiny bits of debris can stop the seat from closing fully, so it weeps constantly. Sometimes lifting the lever briefly flushes it clear. Often it doesn't, and the valve needs replacing.
A failed thermostat. If the tank is genuinely overheating, the valve is doing exactly what it was designed to do. Replacing the valve alone won't fix this, and neither will blocking it. The thermostat or controls need attention, and on gas units that's licensed gas work.
An ageing tank. Storage systems typically last somewhere in the 8 to 12 year range, depending on water quality and the anode. A system past that age that starts dripping and showing rust is often telling you it's near the end.
Do not cap, plug or block it
We see this more than we'd like. Someone gets tired of the drip, blocks the drain line or caps the valve, and the problem goes away. It's the most dangerous option on the list. A relief valve that can't relieve turns a hot water tank into a sealed pressure vessel with a heat source attached. Tanks fail in nasty ways when that happens. Please leave it alone, and don't let anyone convince you a cap is a fix.
Also leave the drain line itself unobstructed and pointing downward. If it's running into a garden bed, over a pavers joint or through a wall cavity, it's worth a conversation about re-routing it somewhere sensible.
When to call us: same day or next week?
Call the same day if the discharge is hot, steady or loud, if you can see steam, or if the unit smells of gas or is behaving strangely. Turn off the power at the switch or the gas at the isolation tap if it's safe to do so, and call. If you suspect an actual gas leak, don't mess about: see our post on whether a plumber can fix a gas leak.
Book in this week if the valve drips steadily but the water isn't hot and the unit is otherwise working. It's wasting water and often means the valve is on its way out.
You can probably watch and wait if it only drips during heating and stops afterwards. Make a note of how long it runs and how much water comes out. If that changes, ring us.
What can you safely do yourself? Not much, and that's deliberate. Lifting the lever for a second or two to flush the seat is something manufacturers mention, but stand clear: the water can be very hot. Replacing the valve, adjusting the thermostat, or touching anything on the gas or electrical side belongs with a licensed tradesperson.

What a repair usually involves
Replacing a relief valve on an otherwise healthy tank is a modest job: the valve and labour typically fall in the $250 to $450 range for most Melbourne homes, depending on access and the type of unit. Adding or replacing a pressure-limiting valve is usually in a similar bracket. If the tank itself is rusting or leaking, a replacement system installed and compliant will generally start from around $1,800 and rise from there depending on the unit, and we'll give you honest numbers on whether repair or replacement makes sense.
What happens when you book us
1. Book online. Fill in the booking form with your suburb, the type of system and what you're seeing. Photos of the valve and the model plate help a lot.
2. We confirm a time. You'll get a window that suits, with same-day slots kept for urgent jobs.
3. We arrive and diagnose. We check pressure, temperature and the valve itself before recommending anything. No upselling a new system when a valve will do.
4. We quote before we start. You'll know the cost up front, in plain language.
5. We fix it and tidy up. The job gets done, the area gets cleaned, and you get a clear explanation of what we found.
What we don't do
To be upfront about it: we're a residential maintenance plumber. We service and repair hot water systems, gas appliances, roofs and gutters, and clear drains. We don't do hydronic heating, air conditioning or new-build construction plumbing, and we'd rather say so than waste your time.
Servicing South-Eastern Melbourne and surrounds
We look after South Yarra, Toorak, Prahran, Windsor, Armadale, St Kilda East, Malvern, Glen Iris, Mont Albert, McKinnon, Black Rock, Chadstone, Moorabbin, Balwyn and Docklands, plus the streets in between.


