Rheem Hot Water System Not Working: What to Check Before You Call
Updated: Nov 13

It's 6:40am, the shower's running, and the water has gone from warm to cold to "why do I live like this". If you've got a Rheem and it has stopped doing its one job, you're in good company. Rheem is one of the most common hot water brands in Melbourne homes and apartments, and when they go off they tend to do it at the least convenient moment.
The good news: a fair share of "no hot water" calls are a switch, a gas bottle or a tripped safety device. The bad news: some of the fixes are strictly licensed work, and we'll tell you exactly where that line sits so you don't hurt yourself or void your warranty.
Step one: is it the whole house or one tap?
Before you touch anything, work out the scope. If only one tap runs cold, the problem is almost certainly that tap's mixer or cartridge, not your Rheem. If every hot tap in the house is cold or lukewarm, the system itself (or its power or gas supply) is the suspect.
Also note the pattern. Hot for two minutes then cold usually points to a heating element, thermostat or burner issue. Hot water that never gets properly hot can be a thermostat setting, sediment, or a tempering valve problem. Completely cold from the first second means the unit isn't heating at all.
Safe checks you can do yourself
These need no tools and no licence. Work through them in order.
Power supply (electric storage and heat pump models). Check the switchboard. A tripped breaker for the hot water circuit is the classic culprit. Flip it back once. If it trips again straight away, stop. That's a fault, not a fluke, and it's an electrician's job. Many Melbourne homes also run electric systems on an off-peak circuit, so check that whatever controls that circuit hasn't been switched off.
Gas supply (gas storage and continuous flow models). Make sure the gas isolation valve at the unit is open (handle in line with the pipe). If you're on LPG bottles, check the bottle isn't empty. Check whether other gas appliances, like the cooktop, are working. If they aren't, the problem is upstream of your Rheem.
Ignition and display indicators. Modern Rheem units use electronic ignition rather than a standing pilot flame. Look for an indicator light or, on continuous flow units, a display. A flashing light or a fault code is the unit telling you what's wrong. Write the code down, along with the model number from the rating label, and have both ready when you call. If you're not sure which model you have, our Rheem and Stiebel identification guide walks through where to find the label.
Thermostat setting. If the system has been serviced recently or someone fiddled with it, the temperature may have been turned down. Hot water in Australia needs to be stored at 60°C or hotter to keep Legionella at bay and delivered at a safe temperature at the tap. Our post on how hot a hot water service should be explains why.
Tripped thermal cut-out. Electric storage systems have a safety cut-out with a reset button, but it sits behind a cover that exposes live wiring. Do not take that cover off. If you suspect an overheat trip, that's a call to a licensed professional. A cut-out that has tripped once usually means something caused it, such as a faulty thermostat, and pressing the button repeatedly just hides the cause.

Where DIY stops: gas and electrical work
We'll be blunt, because it matters. Gas fitting and electrical work are licensed jobs in Victoria. Replacing a gas control valve, burner, thermocouple or ignition component is gas fitting. Replacing an element, thermostat or anything inside the electrical cover is electrical work. Neither is a weekend project, and a botched gas job is the kind of mistake you only make once.
If you smell gas at any point, don't flick switches or use your phone near the unit. Turn off the gas at the isolation valve if it's safe to do so, ventilate the area, leave, and call the gas emergency line. Our post on whether a plumber can fix a gas leak covers what to do and who does what.
Common patterns we see
Sediment and scale. Melbourne water is soft compared with many cities, but older tanks still build up sediment, and a rumbling or popping sound while heating is the giveaway. A service can extend the life of a healthy tank, but it won't resurrect a tired one.
Failed thermostat or element. On electric units, this is the usual reason for lukewarm water or running out far too quickly. It's a repair, usually cheaper than replacement if the tank is in good shape.
Gas burner or ignition faults. Blocked burner, faulty ignition or flame sensor problems tend to show up as a fault light and no heat. These need a licensed gas fitter, and parts availability for older models can tip the decision toward replacement.
Leaking tank. Water pooling under the unit that isn't coming from the relief valve drain or a pipe connection means the tank itself has failed. There's no repair for a corroded storage tank. It's replacement, and it's better done on your schedule than after the ceiling below gets wet. That's a particular worry in apartments, where a failed tank can flood the unit downstairs.
Repair or replace?
As a rough guide, a storage system under about eight years old with no leaks is usually worth repairing. Past ten to twelve years, or with rust around the base, weeping fittings or repeated faults, replacement tends to make more sense than paying for repair after repair. Expect a typical like-for-like replacement of a storage system to land somewhere around $1,800 to $3,500 installed in Melbourne, depending on size, type and access, and a repair call to cost a fraction of that. We'll give you a firm quote on site before any work starts, and we'll tell you honestly if repair is the cheaper road.

When to call vs. DIY
DIY: checking the breaker once, confirming gas supply, checking the display, noting the fault code and model number, and working out whether it's one tap or the whole house.
Call us the same day: water pooling around the unit, a breaker that keeps tripping, any gas smell, fault codes that won't clear, hot water that's scalding or won't stop, or a unit that's making loud banging noises.
Call us this week: lukewarm water, running out faster than before, or a system older than ten years that has started playing up.
What happens when you book us
1. Book online. Fill in the form with your suburb, the problem and the model details if you have them.
2. We confirm. You'll hear from us with a time window, and we'll flag if it's urgent.
3. We diagnose on site. We check supply, safety devices and the unit itself, then explain what we found in plain English.
4. You get a clear price. Repair versus replace, with costs, before we pick up a tool.
5. We fix it and tidy up. Work is done by licensed tradespeople, and we leave the area clean.
What we don't do
Plumb Melbourne is a residential maintenance plumber. We do hot water repairs and replacements, gas appliance servicing, roof and gutter repairs and drain clearing. We don't do hydronic heating, air conditioning or new-build construction plumbing, and we'd rather say so up front than waste your time.
Servicing South-Eastern Melbourne and surrounds
We look after South Yarra, Toorak, Prahran, Windsor, Armadale, St Kilda East, Malvern, Glen Iris, Mont Albert, Mckinnon, Black Rock, Chadstone, Moorabbin, Balwyn and Docklands.



